Traditerm® Perfil arranque aluminio
Starter and protection profile used in the TRADITERM® System. It protect and reinforce the base. Used as a guide for the aligning the insulation panels. It does not rust and its easy to apply. It has a range of thicknesses to choose depending on the thickness of the insulation panel used.
Additional information
Composition
Aluminum profile.
Features and applications
- Easy to apply.
- Marks the start of the TRADITERM® System.
- Protects and reinforces the base of the TRADITERM® System.
- Serves as a guide for aligning the insulation panels.
- Range of thicknesses to choose depending on the thickness of the insulation panel used
Instructions for use
- On the support, draw a level line, on which the TRADITERM® PERFIL DE ARRANQUE will be screwed. The minimum distance between the starter profile and the ground must be ≥ 15 cm.
- The logs that fix the starter profile to the support are placed 30cm apart from each other. The first screw should be placed at a distance of less than 5 cm from the edge of the profile.
- If the surface (on which the starter profile is screwed) is uneven, use profile spacers behind the starter profile, at the points where it is screwed, in order to level the starter profile surface.
- When starting profiles meet, there should always be a separation distance of 2 to 3 mm. This separation can be achieved by using starter profile connectors.
Cautions and recommendations
- At joins between profiles, leave a separation distance of 2 to 3 mm.
- To fasten the profile, apply a screw every 30 cm.
- The fastening should always be at a distance of less than 5 cm from the edge of the profile.
- The thickness of the starter profile is the same as the thickness of the insulating panel.
- The meeting of the support with the TRADITERM® PERFIL DE ARRANQUE must be sealed by
PUMALASTIC MS.
Packaging
Batches of 10 units at 25 linear meters.
The profiles have to be stored horizontally.
Technical data
(Data obtained in a laboratory under standard conditions)
| Composition | Aluminum (0.8 mm) |
| Approx. weight | 0.3 Kg/m |
| Profile lenght | 2,5m |
| For insulation panel thickness | 30, 40, 50, 60, 70, 80, 100, 120, 140, 150, 160, 180, 200mm |
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.