Morcem® Yeso Proyectado
Projected plaster with a high composition of perlite that has exceptional qualities such as: An increase in retention
of water, increased performance thanks to its lower density, the screeding, cutting and plastering operations are easily carried out due to its slow and progressive setting and hardening thanks to the fact that perlite is included in its composition.
This material has a high coefficient of thermal conductivity and, given its porous structure, provides good acoustic and thermal insulation, protection against low temperatures and against fire.
Additional information
Features and applications
- High output.
- Considerable increase in water retention.
- Very easy to use.
- Good paste consistency.
- Low plaster consumption due to its lower density.
- Flexible trowelling and floating due to its perlite content.
- Suitable for coating horizontal and vertical indoor surfaces, such as ceilings and walls.
Instructions for use
- Use pump/spray plastering machines that have been specially designed for the application of this type of plaster.
- Thanks to its mechanical mixing this plaster provides a paste of constant quality and homogeneity. Mixing water 10–11 l/bag. Recommended thickness 1 cm.
- Eliminates the effort of mixing and is much faster to apply than manual plasters.
Cautions and recommendations
- Do not add any kind of additives that could alter the setting process and the final strength of the product.
- Do not add water after letting the product rest, since this may cause an alteration to the product's final strength.
- Be sure to clean tools and mixing equipment thoroughly prior to further batch mixing.
- Facings must be free from dirt, saltpetre, efflorescence or any material that will prevent plaster adhesion.
- Use clean water with a temperature between 5°C and 40°C. Drying time 15–30 days.
Packaging
17 kg plastic-coated paper bags.
Be sure to store this product in a dry place and protect from moisture to preserve its properties.
Storage up to 12 months in its original closed container, sheltered from weather and moisture.
Technical data
| Water/Plaster Ratio | 10–11 litres per bag |
| Powder density | <800 kg/m3 |
| Initial set time | >120 min |
| Shore Hardness C | ≥65 |
| Compressive strength | ≥2 N/mm2 |
| Bending resistance | ≥1 N/mm2 |
| Output | 1.5 m2/sack/cm thickness ±5% |
Note: Workability can vary depending on water/plaster, proportions, temperature, water pH, base type, mixing velocity and time.
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.