Aditivos e imprimaciones

Aliphatic polyurethane resin-based binder for creating and installing decorative natural stone and mineral chippings.

Synthetic mineral render with highly elastic properties, presented in paste form, suitable for waterproofing, protection, and decoration of all types of façades and interior walls. Formulated with additives capable of preventing and delaying the appearance of moulds and algae. Decorative render mortar for the Traditerm External Thermal Insulation system (ETICS).

Crushed rubber from recycled tire, with different sizes and colors. Used for the implementation of continuous and flexible pavement manufactured in situ.

Epoxy antacid two-component mortar for laying and filling of ceramic tiles and mosaics with joints of width between 1 and 15 mm. Resistant to UV rays exposure and weather and climate action.

Geotextile not knitting, formed by cut fibers of Polypropylene of high tenacity 100 %, joined mechanically by a needled and thermo- fixed process, stabilized against UV rays.

Geotextile not knitting, formed by cut fibers of Polypropylene of high tenacity 100 %, joined mechanically by a needled and thermo- fixed process, stabilized against UV rays.

Single-component cementitious adhesive with mixed binders, excellent workability, low dust emission, low VOC emissions and high whiteness. It possesses flexibility and high adhesion, with reduced slip and extended open time, suitable for the installation of interior and exterior floors and walls. Specially recommended for façades, big surfaces and radiant heating floors. For gypsum or anhydrite substrates and very tough applications or those requiring the flexibility of the product.

Powdered material for the complete joint treatment in plasterboard systems. Hardens through a chemical reaction and air-drying.

Magnesium carbonate

Improved white bicomponent reactive adhesive with excellent flexibility, no vertical sliding, ideal for ceramic tiles, mosaics, natural stones, polycarbonate panels and resin conglomerates. Suitable for interior and exterior areas; for both floors and walls. Excellent workability and optimum water resistance. Suitable for the adhesion of different materials on non traditional supports.

MORCEM ELASTIC PM TRANSPARENTE, is a transparent and aliphatic polyurethane resin that, once cured, creates a continuous, elastic membrane, without joints or overlaps, totally watertight and waterproof.
It can be applied by brush or roller.

Single-component polyurethane membrane that produces a continuous, elastic, aromatic membrane completely adhered to the substrate, watertight and 100% waterproof. Its properties make it excellent for its application on all types of surfaces, whether in new construction or rehabilitation.  It has the CE stamp based on a Declaration of Presentations (DoP) made according to the UE305/211 regulation. The MORCEM ELASTIC PM membrane has an ETE 20/0439 certification, with 25 years of useful life for a minimum thickness of 1.5 mm.

The Tejido Carbotec System is composed of a unidirectional carbon fiber fabric wrapped in a weft of glass thread covered with thermoplastic material that allows to maintain the position of the carbon fibres during its implementation. It is supplied in rolls of different widths and lengths.

Transverse butyl deformable cold adhesive strip, composed of a visco-elastic layer covered by a non-woven fabric, resistant to alkalis. Theupport allows adaptation to the shape of the substrate and is highly recommended for specific applications of MORCEM® ELASTIC PM liquid polyurethane, and for elastic cementitious waterproofing systems. 

Waterproof coating with high elasticity based on an aqueous dispersion of self-crosslinking acrylic resins by UV rays, suitable for protection and decoration of all kind of material façades (concrete, cement, brick, etc.) giving the support an excellent resistance to the most thus obtaining a top quality finish and in which contractions of the facing are foreseen that may cause cracks.
Preserves concrete structures from degradation caused by atmospheric agents as well as façades, precast elements, beams, pillars, etc.

One-component, fibre-reinforced, fast-hardening and drying, waterproofing membrane, endowed with high flexibility and extended open time, for waterproofing and adhesion of tiles on traditional substrates.

Carbotec sheets are manufactured through a pultrusion process from carbon fibre filaments arranged in an epoxy resin matrix. There are three different types of sheets: with an elasticity of 170 GPa module (Most commonly used: low modules: LM), of 200 GPa (high module: HM) and 250 GPa (of very high module, for specific applications: UHM).

1 m x 10 m x 4 Kg / m2 sheet of modified bitumen with plastometer (APP), with polyester felt reinforcement, finished with non-stick polyethylene film on the inner side and with mineral granule as protective material on the outer side. It acts as a mono-layer and bilayer system under heavy protection. Suitable in turn for tightness in buried structures and bottom sheet in landscaped roof. 

1 m x 10 m x 4 Kg/m2 sheet of polymer-additivated bitumen with polyester felt reinforcement, finished on both sides with non-stick polyethylene film. Waterproofing bituminous sheet of polymer-additivated bitumen type LA-40-FP.

Decorative solution for the gluing of high performance ceramics; with TECNO-ADAPT technology; with low dust emission; including low VOC emission and bacteriostatic properties; antifungal and anti-algae; anti-florescent and hydro-repellent; quick drying and quick setting; high resistance to abrasion and possesses great plasticity; for the sealing of joints up to 20mm. Grouting of all kinds of ceramic parts, heavy traffic, pools, floors with underfloor heating and for the application in areas where a there is a risk of spreading microorganisms.

Anti-rust primer on metallic substrates, by forming an electronic barrier of cathodic protection.

This additive acts as liquid detergent, which cleans all halo residue from epoxy mortars. It is suitable for cleaning all type of ceramic tiles, including delicate ones, such as lapped ceramics, glass or ceramic mosaics and all kinds of natural stones, even polished.  Apply to remove residues or veils from epoxy mortars such as MORCEMCOLOR EPOXI.  To remove veils on polished porcelain stoneware with dark stains from previous cementitious joints.  To eliminate any possible patina that may show up due to the use of ordinary maintenance surfaces.

A set of unidirectional carbon fibre yarns of high mechanical resistance, housed inside a cotton thread net that gives them a "rope" appearance. Once stiffened with epoxy adhesive, they are used to anchor and structurally connect CARBOTEC systems or other types of structural reinforcement systems to the foundation to be reinforced.

High performance coloured grouting mortar with additives and anti-fungi/anti-algae properties. Fast-setting and fast-hardening, anti-efflorescences and water repellent grout mortar with great plasticity for the sealing of joints from 2 to 20 mm. Highly recommended for areas where the applied product is required to be quickly ready to use and ready for traffic. All type of ceramic pieces grouting in intense traffic areas, swimming-pools, floors with radiant heating systems and for its application in areas prone to the growth of microorganism. 

Universal pigment dispersion free from  solvents base on additives related to pigments.

Waterproofing sheet of 1 m x 8 m x 4.8 Kg/m2 of bitumen modified with elastomer (APP).  With polyester felt armour, finished on both sides with non-stick polyethylene film. Waterproofing bituminous sheet ideal for waterproofing of roofs type LBM-48-FP. It acts as single and double skin under heavy protection. It serves in turn for water tightness in buried structures and, as lower sheet in gardens’ roofs.

Wall anchor plug for insulating panels attachment in the TRADITERM external thermal insulator system. High quality and safety plug.

Mono-component mixed-binder cementitious adhesive with excellent workability, endowed with high flexibility, high adhesion, with reduced slippage and extended open time, for interior and exterior pavements and claddings. Highly recommended adhesive for the placement of exterior façades, large surface paving and underfloor heating, for very demanding applications or those that require a very flexible product.

Powder product, which, when applied on fresh concrete, it makes a monolithic coat with great resistance to abrasion. It has excellent mechanical strengths, and it is easy to clean. Suitable for industrial buildings floors subject to heavy traffic it is also suitable for logistic warehouse floors, shopping centre’s car parks,  or any other similar areas. Without dust formation on the surface.

Low viscosity two-component epoxy resin for injections in concrete.

Coating mortar based on aerial lime.

For power floated concrete or smooth finish on mortar fillings.

Impervious to rainwater and permeable to water vapou

High performance thixotropic mortar for the preparation of floors that, once hardened, creates a coating with high mechanical resistance, strong adherence to the base of application and high resistance to mechanical abrasion. Its consistency makes it suitable for application on sloping pavements. Suitable for thicknesses from 5 to 30 mm. It is used as leveling mortar for ramps and pavements with slopes in garages and industry.

Bicomponent, solvent-free epoxy resin coating. It can be applied on substrates in contact with aqueous foods or drinking water. Provides waterproof coatings with high resistance to abrasion and acids and alkalis.

Coloured epoxy resin mixed with PAVILAND CUARZO 0,2 or PAVILAND CUARZO 0,3, it is used for the production of self-levelling pavements of low thickness (2 to 4 mm) and high resistance. This product for pavements is easy to apply and provides a very smooth and easy to clean finish. Waterproof in interior floors. Available in a wide range of colours. Among its different uses we can find the ones in food, chemical and pharmaceutical industry or even laboratories.

Paviland Fibra Macro CO-PO is a 54 cm long fibre, made of 100% virgin Copolymer-Polypropylene, specially designed for the structural reinforcement of concrete. Its structure made of twisted mono filament fibres, offers maximum durability without the risk of corrosion.

Self-levelling mortar for the preparation of interior floors, which, once it gets hard, it is suitable for any kind of floors (ceramic, wooden flooring, carpet, etc.) 2 to 30 mm thickness. Levelling mortar for interior irregular floors. High mechanical strength and excellent adhesion on cementitious and concrete mortars. This self-levelling mortar has a great workability and fast setting capacity. 

Product based on the dispersion of a pure acrylic methacrylate resin that is recommended as a finish on concrete and printed concrete floors, protecting them from external agents by sealing the pore. This product improves the features of printed concrete, providing it with a uniform and shiny finish. Due to its thin particle size, it has very good anchorage on the pavement and increases its cohesion. Thanks to the components involved in its formulation, it provides the substrate with a decorative and very resistant layer which accentuate the properties in the pavement and increases its durability.

MORCEMDRY PU UV Varnish is a bi-component aliphatic polyurethane elastic render with solvent.
It provides UV resistant, elastic, protective films with high resistance to industrial, polluting atmospheres

Adhesivo Carbotec Lamina is an epoxy resin. Bi-component resin and free from solvents.  It has great adhesion to all types of substrates, even without primer and high resistance to abrasion.

Single-component, lightweight, high-performance, cementitious adhesive with mixed binders and excellent workability, low dust emission, low VOC emission, endowed with flexibility and high adhesion, with reduced slip and extended open time, for the installation of interior and exterior floors and walls. This adhesive is particularly recommended for the installation of façades, large surface floors and radiant heating floors. Suitable for gypsum or anhydrite substrates.

Single-component cosmetic repair mortar for rendering and levelling concrete floors, which enhances the aesthetic appearance of the floors and its water resistance. 1 to 3 mm thickness. This product is suitable for floors. It has an excellent adhesion on concrete; it can also be used as levelling mortar for concrete floors and preparation of substrates for protective rendering. It is water and weather resistant.

Powder product which, when applied on fresh concrete, it makes a monolithic layer with great resistance to impact. Great resistance to abrasion. And easy to clean. Ideal for industrial building floors and hypermarkets subject to heavy traffic. Resistant to open air. Without dust formation on the surface.

Specially formulated cementitious adhesive, non-sagging, for thick-bed installation in direct tiling on brick walls without the need for prior plastering and on floors with irregular substrates. Suitable for interior and exterior areas. Highly recommended for porcelain floors in new constructions. Suitable for all type of ceramic pieces, marble, and granite stone bonding.

White crushed marble is available in various grain sizes and is commonly used for manufacturing pebbles, prefabricated elements, decoration, gardening, etc.

Paviland AR Glass Fibre is a high-integrity, alkali-resistant chopped glass fibre designed for use in reinforcing concrete and mortars.

Cementitious adhesive of mixed binders with excellent workability, endowed with flexibility, great adhesion, with reduced slip and extended open time, for the installation of interior and exterior floors, interior walls, and exterior plinths. Laying of new flooring on top of existing flooring and underfloor heating. Adhesion of all types of ceramic pieces, porcelain stoneware, marble, granite, and natural stone. Suitable for gypsum or anhydrite.

Thin-layer adhesive mortar for cellular concrete block manufacturing.

Two-component epoxy resin primer for application on low-porous concretes as well as a levelling coating for decorative and industrial floors.

Liquid resin in a solvent medium, suitable for sealing and protecting flooring It is made from polymers based on methacrylate dissolved in aromatic solvents. It hardens through the evaporation of solvents and works by increasing the cohesion of the flooring, creating a decorative and highly resistant layer that enhances the properties of the flooring and increases its durability.

Matte coating based on acrylic copolymers, indicated for the protection and decoration of façades of any kind of material (concrete, cement, bricks, etc.), providing the substrate with an excellent resistance against any environmental condition. With an excellent finish quality.
Preserves concrete structures from degradation caused by atmospheric agents as well as façades, prefabricated elements, beams, pillars, etc.
 

Sealer based on high-quality silicate emulsion, suitable as base for the subsequent application of Morcemcril Silicato. It Improves adhesion, it makes the application easier, homogenizes the absorption of the substrate and gives an initial coloured coverage.
It favours the coverage and performance of the finish acrylic mortar, maintaining high permeability to water vapour. Excellent application, workability, and adhesion to the substrate.

PVC-P synthetic sheet obtained by co-extrusion. Especially designed for tanks and pools waterproofing intended to contain liquid food substances and drinking water.

5 x 20 mm rectangular bead made from hydro-expansive polymer for sealing concrete joints, offering excellent durability.

Weatherproof water based polyurethane membrane.
Coating for horizontal substrates based on acrylic polymers and aliphatic polyurethane. It forms a continuous and elastic high-performance coat capable of preventing water infiltration and the resulting moisture-related issues.
Especially suitable for preventing water infiltration on terraces, rooftops, roofs, partition walls, expansion joints, channels, downspouts, etc. It can be applied to any exterior surface that is occasionally walkable, provided it is not subjected to daily or intensive traffic.

Adhesive mortar for rendering and for fixing insulation materials (glass fibre or rock wool) to walls.
It is rainwater proof and permeable to water vapour, allowing the system to breath. Also a fire-proof system.

One-coat mortar for decoration and waterproofing of façades. For hand or pump application directly on the brick. Large variety of finishes.

Protects glazed or non glazed ceramic tiles from pigmented stains.
Apply on the surface of the tile avoiding the joints.

Dry mortar for façade, indoor jobs, patios, etc finishes. Rainwater-proof and permeable to water vapour. For plastering and masonry jobs in general.

Refractory mortar for setting refractory bricks and to plaster areas subjected to very high temperature.     

Powder product, which, when applied on fresh concrete, it makes a monolithic layer with great resistance to abrasion. Suitable for industrial floors. Paviland Industrial has excellent mechanical strength and great resistance to abrasion. Available in a wide range of colours. Resistant to open air.

Powder product to be applied on fresh concrete, creating a monolithic surface layer with high abrasion resistance and a pleasant texture that can replace traditional pavements (paving stones, natural stone, slate, etc.). It can be used on streets, pavements, exterior areas, access to shopping centres, urban roads with pedestrian and vehicle traffic, accesses and surrounding areas of single-family homes, swimming pools, urbanizations, etc.

Mortar waterproofer. It improves traditional mortars qualities.

Satin plastic paint intended for the protection and decoration of walls made with all kinds of mineral materials (concrete, cement, plaster, etc.) both indoors and outdoors.

Adequate for painting sport fields.

Product based on the dispersal of styrene acrylic resin with low water absorption.  Is has good resistance to alkalis and yellowing, as well as great flexibility and durability in the exterior. Recommended as curing liquid with an aqueous base, best for printed paving.

Specially formulated product to diminish the cracking tendency in mortars or concrete due to retraction.

One-coat mortar.
Specially designed for texturing of interior and exterior coatings.
For hand or pump application directly on the brick.
Rainwater proof and permeable to water vapour.
Wide range of decoration possibilities by combination of colours and textures.

Deep hardening primer to bind substrates prone to disintegrate before applying One-coat Mortars, Cementitious Adhesives, Levelling Mortars, etc.

Dry mortar with special additives with the necessary fluidity and time to be applied with a mortar projection pump.

High-strength mortar for filling and anchorage of machinery, leveling supports and bridges, etc.Medium and thick layers.

Renovation mortar for the treatment of damp by capillarity on the lower parts of the wall, facilitating the evaporation of water retained in the wall.

1m x 12m x 3kg/m² non-reinforced membrane made of bitumen with polymer additives, with metallic self-protection, finished with a natural or red color 80 micron embossed aluminum sheet on the outside and non-stick polyethylene film on the inside.Non-reinforced bituminous waterproofing membrane made of bitumen with polymer additives, with metallic self-protection, of the type LA-30/M-NA.

Two-component thixotropic epoxy adhesive; like multipurpose adhesive for most construction materials; suitable for filling joints, cracks and small holes.

Natural hydraulic-lime mortar(i.pro CALIX NHL 3,5 de FYM-Heidelbergcement Group) for rendering. Natural composition, highly breathable.

Waterproofing coating with high elasticity and flexibility. It is used as a coating on horizontal surfaces to which it provides continuous coverable capable of preventing water seepage and the consequent problems resulting from dampness.It is a coating that completely adheres to the surface, with high flexibility, elasticity and mechanical strength, excellent durability and very low residual tack of the dry film.It is especially suitable for preventing water seepage in terraces, flat roofs, tiled roofs, party walls, expansion joints, channels, downspouts, etc,…In general, it can be applied on any external surface that may be passable provided that this is not daily or intensive.

It is an ecological stabilised soil made of natural aggregates and binders, which give to it their mechanical properties.

Class R4 mono - component high performance repair mortar suitable for large thicknesses. Formulated with sulphate resisting cement.

Bonding primer for Self-levelling Cement Systems by Grupo Puma, for interior and exterior use. Its high penetration performance on the substrate helps it to act as a substrate sealant and bonding primer.

This quick-setting plaster for manual application offers the ideal solution for supporting frames and rulers, as a bonding agent for bricks and other building material for interior partitions, and for holding electrical boxes and conduits. The application procedure is very simple and gives fast results.

Transparent epoxy resin of low viscosity, 100% solids, which mixed with arid from PAVILAND CUARZO or PAVILAND CUARZO COLOR range,  is used for the fulfilment of decorative pavements or industrial pavements

A two-component primer based on very low-viscosity epoxy resins, for application on low-porous concrete. It adheres well to PAVILAND EP systems. It is very easy to apply. Among other applications, its use consolidates concrete or mortar floors.

Powder filler for plastering, to smooth out, fill in cracks, scrapes, holes, etc., ideal for plastering plasticized Gotele surfaces.

PAVILAND® ULTRA RÁPIDO is a dry compensated retraction concrete intended for fixing, supporting and repairing elements that may require high initial strengths and quick opening to transit. Its applications include the fixing of manhole frames, manholes, urban furniture, road repair, filling and anchoring of road signs, repair of industrial floors. It has a great adherence to concrete and quick opening to transit.

Lightweight fast-drying mortar for floor screeds, up to 5 cm.

Acrylic resin base mortar for layers levelling of the surface in sports and pedestrian areas or in bicycle lanes.  This pavement product is very easy to apply and it’s suitable for the compensation of irregularities. It is a water base product suitable for indoor and outdoor floors.  Also suitable for car park areas with little traffic. Black colour.

Two-component water-based epoxy primer/ bonding bridge for preparing damp and dry surfaces.

Two-component cementitious adhesive with high-performance for demanding applications Specially recommended for the installation of big format pieces on big surfaces (façades and floors). Perfect adhesive for all kind of ceramic tiles in both outdoors and indoors. Reduced slip and excellent initial adhesion.

Adhesive made of mixed bonding agents with an excellent workability, great flexibility, high adherence, reduced slipping and extended open time. Suitable for the application of interior and exterior pavements and claddings. Suitable for the placing for all kind of ceramic pieces. Specially recommended for façades and big surface pavements and floorings with underfloor heating systems. Suitable for plaster or anhydrite substrates and very demanding applications or that require the flexibility of the product.

Cementitious adhesive made of mixed bonding agents, fast hardening and drying properties, with reduced slippage. Suitable for indoor and outdoor cladding on floors and walls. Once hard, does not contain soluble salts that stain the stones or cause efflorescence to exterior facings. Especially suitable for fixing to façades, large areas of flooring, floors with underfloor heating and whenever a fast turn around time is required. It permits bonding all types of ceramic tiles or elements with similar characteristics.

Ready to use adhesive made with resins, and specific additives and agents. Suitable for fixing any kind of ceramic cladding on vertical interior or exterior substrates. Highly flexible. Ideal for gluing exhibitions on wood and old tiles. This adhesive is perfect for use on deformable supports.

Ready to use adhesive made with resins, and specific additives and agents.
Suitable for fixing any kind of ceramic cladding on vertical interior or exterior substrates. Highly flexible.
Ideal for gluing exhibitions on wood and old tiles. This adhesive is perfect for use on deformable supports.

Thermal insulation panel made of self-extinguishing expanded polystyrene, used in the TRADITERM® external thermal insulation system. The expanded polystyrene panel is used as insulation within the TRADITERM® System both in new and restoration work. Its a light and workable material, also easy to cut. The range of thicknesses provide different levels of thermal insulation. It has an excellent resistance to aging.

Paint of acrylic resins in aqueous dispersion, specially designed for applications in swimming pools. Product of easy application, very good coverage and ideal for permanent contact with water.

Matte coating based on HYDROPLIOLITE resin, indicated for protection and decoration of façades of any kind of material (concrete, cement, bricks, etc.), providing the substrate with an excellent resistance against any environmental condition. With an excellent finish quality. Permeable but porous to water vapour. Highly recommended for substrates with humidity caused by capillarity or breathable. Thanks to its small particle size, it is a self-priming paint.

Adherence promoter, specially developed for the placement of resin pavements on non-porous and/or vitreous surfaces such as ceramics, stoneware, marble, stone, very low porosity concrete, polished cement, etc. Paviland Primer Ceramic makes a quick "wetting” easier on the above-mentioned surfaces, which results in the formation of substrate-polymer type bonds. In general terms, it favours the union between dry silica surfaces and polymerized liquid resin.

Coating mortar based on aerial lime. For plastering with a fine scraped, floated or smooth finish, both on cement mortar rendering and directly on the cladding. Impervious to rainwater and permeable to water vapour.

Resistant synthetic-mineral render, suitable for waterproof, hydrophobize and decoration of all types of façades and interiors with siloxanes, on walls and ceilings with siloxanes, on walls and ceilings. Decorative render for the TRADITERM® External Thermal Insulation System (SATE/ETICS).  Formulated with additives capable of preventing and delaying the growth of mould and algae, it also incorporates hydrophobic properties that prevent temporary moisture absorption and reduce soiling caused by it.

Product that provides continuous coverage capable of preventing water seepage and the consequent problems resulting from dampness. It is a coating that completely adheres to the surface, with high flexibility, elasticity and mechanical strength, and which withstands excellently the conditions of its application outside and keeps its properties for a very long time due to its excellent durability.It is especially suitable for preventing water seepage in terraces, flat roofs, tiled roofs, party walls, expansion joints, channels, downspouts, etc,… In general, it can be applied on any external surface that may be passable provided that this is not daily or intensive.

Dry mortar for façade, indoor jobs, patios, etc finishes, rainwater-proof and permeable to water vapour, for plastering and masonry jobs in general.
 

Dry mortar for plastering and masonry jobs in general.

Special adhesive to glue and grout glass blocks. Hight plasticity, resistance and water proofing qualities.

Colorless hydrophobic primer recommended for the impregnation and protection of mineral substrates, renders, facing bricks and natural stone façades. It has excellent properties as a water repellent. This primer acts as an excellent barrier to capillary water absorption without forming a film on the substrate. It does not clog pores. Maintains high water vapor permeability. Prevents harmful effects caused by moisture by avoiding them or at least reducing and delaying the occurrence of damage.

For removing cement, glue, plaster, paint and cement-based stucco when cleaning claddings and ceramic floorings.

Matt paint based on acrylic copolymers, recommended as a decorative and protective coating on all types of vertical surfaces and ceilings such as concrete, brick, plaster, cement, and all types of mineral substrates both indoors and outdoors. Excellent workability and easy application, achieving maximum coverage and whiteness.

Matte plastic paint used as a decorative and protective coating on all types of vertical surfaces and ceilings in constructions, such as concrete, plaster, cement, fibre cement, etc.

Product based on the dispersal of pure acrylic resin, which can be used directly as a finishing film for concrete paving and printed concrete, protecting them from external agents by sealing the pore.
Applied on printed concrete, this product improves its finishing, giving a uniform and brilliant appearance.
Due to its small particle size, it has good anchorage to the paving and increases its cohesion.
Recommended as curing liquid with an aqueous base, best for printed paving.

Coloured, water-repellent, and additive mortar with mixed binders, characterized by high fineness and plasticity. Designed for sealing joints of up to 15 mm in all types of ceramic renders. 
Especially suitable for grouting low-porosity tiles (porcelain stoneware) and pools; with anti- fungal and anti-algae preservative. 

High resistance monocomponent R4 repair mortar for large thicknesses.

Product for protecting coatings based on a pure acrylic resin dispersion which can be used for finishing stamped mortars, protecting them from external agents by sealing the pores.This product, when applied on stamped mortars, improves their characteristics, giving them a uniform appearance.It increases cohesion due to its fine particle size.

Lime mortar for wall covering and decorating.
Outdoor and indoor.

High-strength mortar with self-leveling controlled expansion and no retraction.Medium and thick layers.

Low-viscosity, anionic bituminous emulsion to be applied cold as a primer of surfaces.Officially approved according to standard UNE 104-231 (Type EA) DBI 2282. Fluid product, with a uniform appearance and dark brown colour. Non-toxic, non-flammable product. Good adhesion to wet and dry surfaces. Totally stable and long lasting. Hardens by breaking the emulsion due to the evaporation of water from the continuous phase.

Dry-mix concrete.

1m x 12m x 3kg/m² membrane made of bitumen with polymer additives, with fiberglass reinforcement, finished with non-stick polyethylene film on both sides.Bituminous waterproofing membrane made of bitumen with polymer additives of the type LA-30-FV.

ANTISALMOR is a water-based product for removing and preventing the appearance of efflorescence caused by saltpeter on typical construction site facings, such as mortar, concrete, brick, fiber cement, natural stone, etc. It has great penetration in the support and great capacity of dissolution of the salts. This additive prevents the crystallization of salts on the treated surface. It is transparent and colourless and capable of cohering loose or poorly adhering particles.

1m x 10m x 4kg/m² plastomer (APP) modified bitumen membrane, with fiberglass reinforcement, finished with non-stick polyethylene film on both sides.Bituminous waterproofing membrane of the type LBM-40-FV.

Ready to use synthetic mineral render for waterproofing and decorating façades and indoor walls, especially designed for reinforcing skirting boards (baseboards) in the TRADITERM external thermal insulation system. Outdoor and indoor application. 2.  Decorative finish for the external thermol insulation system TRADITERM®. (ETICS).Formulated with additives that prevents and  delay the apparition of algae and molds.

Normal-setting flowable screed mortar for the preparation of interior floors, which, once hardened, is to be covered by discontinuous floor coverings (parquet, carpet, ceramic hardened, to be covered with discontinuous coverings.Flowable interior floor screed mortar for pedestrian traffic. This flowable screed mortar is suitable for underfloor heating.

Natural hydraulic-lime mortar for coating.Natural composition, highly breathable.

Tile adhesive special for its fineness, plasticity and thixotropy for indoor floor tiling and cladding jobs.
Suitable for bonding ceramic tiles with a medium-high adsorption rate.

Two-part epoxy resin-based product with very low viscosity, suitable for bonding fresh concrete or self-levelling mortars to hardened concrete, and hardened concrete to other materials. Its low viscosity makes it ideal for airless application. Very good penetration into the substrate. Suitable for interiors and exteriors.

Acrylic resin-based mortar for the application of adhesive layers and regularisation layers to sports and pedestrian surfaces or cycle lanes.

Projected plaster with a high composition of perlite that has exceptional qualities such as: An increase in retention
of water, increased performance thanks to its lower density, the screeding, cutting and plastering operations are easily carried out due to its slow and progressive setting and hardening thanks to the fact that perlite is included in its composition.
This material has a high coefficient of thermal conductivity and, given its porous structure, provides good acoustic and thermal insulation, protection against low temperatures and against fire.

Bi-component primer based on epoxy resins, of high viscosity, for application on very porous concrete. Paviland Primer EP HV is an adhesive flooring product for the PAVILAND EP systems. It also offers easy application. Among its functions is the consolidation of concrete or mortar floors.

Bi-component primer, formulated with epoxy resins in aqueous dispersion, for epoxy coatings. Acts as an adhesion layer for PAVILAND EPOXI-CEM. This product for flooring is adherent on damp supports and young concrete. It also boasts easy application. Among its functions is that of consolidating concrete or cementitious mortar floors.

Great stability glass fibre mesh for the reinforcement of cementitious mortars.  Suitable for Paviland Arq system. It provides the system with great resistance, stability and it avoids cracks that may appear due to movements in the substrate.

Powdered material for the complete joint treatment in plasterboard systems.

Ready-mixed putty for the coating and smoothing of rough surfaces preparing them for the decoration layer.

Lightweight insulating mortar of closed texture for  FORGED STEEL AREAS AND  FLAT BUILT-UP ROOFING WITH THE DIRECT APPLICATION OF THE FINISHED PRODUCT OR THE WATERPROOF SHEET.

Decorative and waterproofing one-layer mortar for façades. Manual or mechanical application directly on the brick. Great variety of options.

Colourless water-repellent by impregnation and waterproofing which can be used in the treatment of mineral substrates, especially for work finishing’s with mortar façades and natural stone.

Tile adhesive made of mixed bonding agents with reduced sliding and expanded open time, for the placement of all types of ceramic pieces, granite and marble parts on interior and exterior pavement and interior coverings. 

Cementitious adhesive with mixed binders, excellent workability, low dust emission, low VOC emissions and high whiteness. It possesses flexibility and high adhesion, with reduced slip and extended open time, suitable for the installation of interior and exterior floors and walls. Specially recommended for façades, big surfaces floors and radiant heating floors. Suitable for gypsum or anhydrite substrates.

Adhesive made of mixed bonding agents with an excellent workability, great flexibility, high adherence, reduced slipping and extended open time. Suitable for the application of interior and exterior pavements and claddings. Suitable for the placing for all kind of ceramic pieces. Specially recommended for façades and big surface pavements and floorings with underfloor heating systems. Suitable for plaster or anhydrite substrates. 

Hydraulic mortar designed for the cladding of panels for exterior cladding, compatible with panels from different suppliers based on internal tests carried out by Grupo Puma. Ask for more information. This mortar has a high adhesion and strength suitable for use as a lining mortar. as a coating. It is impermeable to rainwater and permeable to water vapour. Reaction to fire Euroclass A1.

Improved thermal insulation panel made of self-extinguishing expanded polystyrene, used in the TRADITERM® external thermal insulation system. The expanded polystyrene panel is used as insulation within the TRADITERM® System both in new and restoration work. Its an excellent thermal insulator thanks to its very low conductivity. Its composition makes it a lightweight and workable material. Its range of thicknesses provide different levels of thermal insulation.

Synthetic-mineral matte coating for waterproofing, damp-proofing and decoration of all types of façades, interior walls and roofs, always keeping its transpiration. Based on acrylic copolymers and silicone resins. Its water-repellent properties prevent the temporary absorption of moisture and reduce the fouling caused. Silicone resins constitute a mineral-type coating and are therefore permeable to water vapour. The combination of high permeability and high breathability makes silicone resin paint the highest quality product for covering façades, which is the reason for its extraordinary durability and dirt repellent.

Fast hardening cement adhesive in fluid format, for indoor and outdoor floor tiling jobs, specially recommended for large areas and for floors with underfloor heating systems. Suitable for bonding all types of ceramic tiles.fIt has a fast curing and excellent bonding.

Decorative and waterproofing one-layer mortar for façades. Manual or mechanical application directly on the brick. Impervious to rainwater and permeable to water vapour. Thin scraping finish.

Dry mortar with special additives, rainwater-proof and permeable to water vapour with the necessary fluidity and time to be applied with a mortar projection pump.

Coloured mortar to be used in masonry jobs.

Mixture plasticizer by air occlusion in the mix.

Adequate plastic paint for interior work, on vertical and horizontal cement, plaster, stucco, etc. mortar facing.

Product based on the dispersal of pure acrylic resin, which can be used directly as a finishing film for concrete paving and printed concrete, protecting them from external agents by sealing the pore.
Applied on printed concrete, this product improves its finishing, giving a uniform and brilliant appearance.
Due to its small particle size, it has good anchorage to the paving and increases its cohesion.
Recommended as curing liquid with an aqueous base, best for printed paving.

Corrosion protection for steel reinforcements from the Morcemrest restoration system, in compliance with EN 1504-7. This product can be combined with other repair mortars from the Morcemrest range. Cementitious anti-corrosion mono-component primer, modified with polymers for protecting reinforcement. When mixed with water a grout is obtained which is applied to the previously cleaned steel. Due to its high pH (approximately 12) level Implarest C creates a passivation layer on the surface of the reinforcement, halting the corrosion process. Implarest C is a corrosion protector classified in compliance with EN 1504-7.

Rendering and decoration lime mortar for both interior and exterior walls.

Demolding liquid with immediate action.
It forms a non-oily film that allows for immediate demolding of concrete cast.

Mortar for high abrassion resistance stamped pavements in 5 to 20 mm thickness.
Fine texture and stamping. Suitable to replace ordinary pavements (slabs, bricks, stones, slate and any continuous flooring with industrial finish).
Can be used as a hydratation layer (fresh over fresh).

Dry-mix concrete, intended for highly permeable flooring systems; constitutes an alternative to traditional flooring aesthetics. It reduces and/or prevents the surface flow of rain water or any other type of water by allowing permeation.It complies with Royal Decree 505/2007, of 20 April, which approved the basic conditions of accessibility and non-discrimination of people with disabilities for accessing and using developed public spaces and buildings.Paviland Drainage is free of resins so it does not emit volatile organic compounds that are harmful for the person applying the product and the environment.

1m x 10m x 4kg/m² membrane made of bitumen with polymer additives, with fiberglass reinforcement, finished with non-stick polyethylene film on both sides.Bituminous waterproofing membrane made of bitumen with polymer additives of the type LA-40-FV.

Waterproof covering with high elasticity and flexibility. Suitable for avoiding water leakage on terraces, rooftops, roof tiles, expansion joints, downpipes, etc. For repairing areas with existing cracks, or with a tendency to split. It provides continuous coverage capable of preventing water leakage and the subsequent problems deriving from humidity.

Self-leveling mortar of great fluidity, normal setting and that once hardened creates a screed of great flatness and mechanical resistance. Suitable for interior self-leveling screeds from 10 to 50 mm in adhered screeds and from 50 to 100 mm in floating screeds. Once hardened, it should be covered by discontinuous pavements (ceramic and others). This self-leveling mortar has great leveling capacity, even in large thicknesses. Suitable for interior floor screeds. Radiant heating floors.

Synthetic resin that is in use as promoter of adherence and primer fillers on supports of mineral, like cement or ceramic nature. Primer for PAVILAND ARQ systems and NIVELAND and PAVILAND levelling pastes. For indoor and outdoor application. Improves adhesion to the substrate, preventing the loss of water and the formation of bubbles.At the same time, it also improves the waterproofing and durability of the Paviland Arq systems.  Primer for covering pores on mineral supports and concrete surfaces. 

Powder product which is applied over fresh concrete to form an abrasion resistant monolithic coat, with short-term high mechanical strengths. The finishing, printing or texturing allows traditional flooring to be substituted (cobblestones, natural stone, slate, etc).

Finely granulated, coloured coating used as an intermediate layer for sport surfaces.

Slow setting plaster for manual application, suitable for coating interior ceilings and walls, over all types of substrates. Its working time is regulated during the manufacturing process, ensuring a reduced waiting period and greater working time, leading to high productivity and excellent finish quality with high mechanical strength. Thanks to its porous structure, it provides good acoustic insulation. It also controls humidity, for optimal comfort indoors. It is non-combustible and provides good fire resistance.

Natural hydraulic lime smoothing mortar.
Natural composition, highly breathable.

Ready-mix material for the complete joint treatment in plasterboard systems.

R4 high resistance mono-component mortar for thick applications.
Formulated with Sulfo-resistant cement, selected aggregates and additives; reinforced with fibres.

Tile adhesive for indoor floor tiling and cladding jobs suitable for bonding ceramic tiles with a medium-high absorption rate.

Lightweight, fast-drying insulating semi-dry mortar for screeds, tiles and roofs. Perfect for sloping and flat roofs, screeds of light slabs and insulation in new construction or rehabilitation. This semi-dry mortar can be used as a complement of floor insulation. Also for floating floors and quick-drying light screeds for all types of flooring.

Two-components primer based on epoxy resins, without solvents, of very low viscosity, suitable as  humid substrates primer and vapour barrier.
 

Cementitious adhesive with mixed binders, excellent workability, low dust emission, low VOC emissions, and great whiteness, high adhesion, with reduced slip and extended open time, suitable for the installation of interior and exterior floors, interior walls and plinths. Installation of new flooring on top of existing one and radiant heating floors. Adhesion of all types of ceramic pieces, porcelain stoneware, marble, granite and natural stone. Suitable for gypsum or anhydrite substrates.

Acrylic render for waterproofing, protection, and decoration of all types of façades and interior surfaces. Decorative render mortar for the Traditerm External Thermal Insulation system (ETICS).

Normal setting cementitious adhesive, with reduced slip and extended open time, for interior and exterior floors, and interior walls. Specially recommended for tiling swimming pools with glass mosaic and interior drywalls (type PYL). For bonding ceramic tiles with medium to high absorption, marble, mosaic, and glass paste.

Single-component white mortar with extraordinary adhesion to polystyrene and exceptionally low capillary water absorption. Designed for application as an adhesive for expanded polystyrene insulation panels (Traditerm Panel EPS), graphite expanded polystyrene (Traditerm Panel EPS-G), mineral wool (Traditerm Panel MW), and natural cork (Traditerm Panel Corcho) and as a reinforced render for these materials. It supports finishes from the Morcemcril range and Morcemdur ITE mortar. It can be applied for the renovation of façades, as a reinforced base coat on render or cement-based screed substrates. For this application, the finish will be from the Morcemcril range. Applicable by hand or by spraying.

Natural expanded cork agglomerate used as thermal-acoustic insulation in the Traditerm Nature System (EWI/ETICS), suitable for both new buildings and restoration work. This product is suitable for the TRADITERM® exterior thermal insulation systems. It gives a 100% natural insulation and highly breathable. The range of thicknesses that provide different levels of insulation. Its a light and workable material, also easy to cut.  

Matte coating based on acrylic copolymers with siloxane, indicated for the protection and decoration of façades of any kind of material (concrete, cement, bricks, etc.), providing the substrate with an excellent resistance against any environmental condition. With an excellent finish quality. Product available in our Easy-Colours tintometer system.

Especially designed for waterproofing in situ using a sandwich structure. Application between two layers of Pumaflex acrylic rubber.

Air-entraining and fluxing agent for mortars.

Adherence primer to promote cement, lime-based mortars and/or plaster-based renders´anchorage on smooth concrete or substrates lacking superficial absorption.

Product in powder form highly recommended to be used on stamped concrete. Avoids adhesion of moulds to concrete improving their release from the stamped concrete.

Product indicated for the regularisation of vertical surfaces with plastic or paint coatings (except for silicates or polyurethanes), concrete, stuccoed walls or mortar or ceramic plastering.

High quality acrylic base, indicated as colouring base for MORCEMCRIL products range. It Improves adherence, it makes the application easier, homogenizes the substrate and gives an initial coloured coverage. It favours the coverage and performance of the finishing acrylic mortar, maintaining high permeability to water vapour. Excellent application, workability and adherence to the substrate.

1m x 10m x 4kg/m² plastomer (APP) modified bitumen membrane, with polyester film reinforcement, finished with non-stick polyethylene film on both sides.Bituminous waterproofing membrane of the type LBM-40-FP.

Covering and protective paint for vertical walls, highly breathable. Particularly suitable for restoration of façades and other mineral surfaces. Provides a matt finish to painted surfaces.

TRADITERM® MALLA consists of double weave threads, essential for reinforcing the TRADITERM® panels. Recommended in the application of TRADITERM® exterior thermal insulation systems. Giving the system greater resistance and stability, and preventing the appearance of cracks caused by temperature differences or movement of the insulation panels. Excellent traction resistance and improves impact resistance.

Liquid product best for paving protection, composed of an acrylic copolymer dissolved in aromatic solvent.  Hardens through evaporation of solvents and acts by penetrating and compacting the particles, increasing paving cohesion both in interior and exterior applications.

Macroporous dehumidifying natural hydraulic lime mortar for remediating damp walls. Natural composition, highly breathable. Classified R, rendering/plastering mortar, complies with regulation EN 998-1. 

Epoxy 100% solid, two-component adhesive, specially formulated for bonding new and old concrete. Once mixed a semi-fluid liquid is obtained which may be applied above 10ºC. It can be used as protection barrier of the steel of the reinforced concrete. It will be applied on the clean reinforcement.

High-conductivity grout for pumping, injecting and filling in geothermal plant heat exchangers.

Self-levelling Mortar of great fluency, fast dry and once  it gets hard, it create a slab of great flatness and mechanical resistance. Suitable for the accomplishment of self-levelling interiors from 10 to 50 mm in adhered screeds from 50 to 100 mm in floating screeds . Once hardened it must be covered by discontinuous pavements (ceramics, etc) or constant (paintings epoxy, etc). This self-levelling mortar has great levelling capacity, even in large thicknesses. Suitable for indoor floors. Radiant heating floors.

Water-based paint consisting of acrylic resins, micronized fillers, and single-component pigments that acts as a decorative finish coat and sealer on sports flooring and cementitious, concrete and pavements. These kind of pavement products have aesthetic finish; they are easy to apply and strong. It has good resistance to ultraviolet rays and does not fade. It is a water-based product with mineral loads.

Carbotec impregnante adhesive is a resin which, due to its impregnation and thixotropy allows the adherence of the carbotec tissue on concrete elements, reinforced concrete or brickwork.

Lightweight and insulating structural concrete for reinforcing floors and reducing thermal bridges. Due to its low density and its flexibility of use, the product is particularly suitable for renovation, it provides high thermal resistance and lightness qualities to the work. This structural concrete is suitable for both, light mixed and collaborative slabs. 

Tile adhesive for indoor floor tiling and cladding jobs suitable for bonding ceramic tiles with a medium-high absorption rate.

Self-compacting high-resistance fluid mortar and balanced retraction.

PAVILAND ASFALTO EN FRÍO has all the properties of a traditional warm agglomerate with the advantage of not requiring being heated.  There is no need of using all those tedious means required for hot-mix asphalt. Once it has been placed, it provides the very same properties as a traditional agglomerate of a tread layer:  It is durable, stable and flexible.

Tile adhesive special for its thixotropy and creamy texture for setting indoor and outdoor ceramic flooring, indoor walls, and baseboards. Suitable for bonding ceramic tiles with a medium-high absorption rate. It has excellent initial adhesion and its creamy texture makes it easy to apply.

Hydraulic mortar used as an adhesive and covering on expanded polystyrene boards (TRADITERM PANEL EPS), expanded polystyrene graphite (TRADITERM PANEL EPS-G), mineral wool (TRADITERM PANEL MW) and natural cork (TRADITERM PANEL CORCHO), in the external heat insulation system Traditerm (SATE/ETICS). This mortar, ideal for exterior thermal insulation system, has great adhesion, waterproofing, easy application and does not spread the flame. It is permeable to water vapour.

Fiberglass mesh with anti-alkali treatment and double twist threads, which combined with TRADITERM® Mesh, is used as a reinforcement to increase the impact resistance of those areas of the TRADITERM® System exposed to direct knocks. Ideal for reinforcing skirting boards (baseboards). It is fire resistant. TRADITERM® MALLA DE REFUERZO is resistant to cracking. Excellent tensile strenght and great flexiblity. In addition, it has a high resistance to shock.

Cementitious adhesive of mixed binders, endowed with flexibility, great adhesion, with reduced slip and extended open time, for laying interior and exterior floor and wall tiles. Specially recommended for façades, big surfaces floors and radiant heating floors. This adhesive is ideal for bonding all types of ceramic pieces.

Additives and coloured mortar of mixed binders endowed with great fineness and plasticity. Suitable for sealing of joints from 2 to 15 mm in all kind of ceramic cladding. Especially suitable for low porosity pieces (ceramic tiles) 

HIGH ELASTICITY waterproof elastomeric coating formed by an aqueous dispersion of self-crosslinking acrylic resins by UV rays, pigments and special additives; intended for the protection of all type of materials (concrete, cement, brick, etc...) in which contractions of the facing are expected to cause cracks. also suitable for substrates with cracks that may cause moisture problems. Product available in our Easy-Colours tintometer system.

Liquid antifreeze for mortars, chloride-free.

Self-levelling mortar for indoor floors preparation. Once hardened, it is suitable for all kind of light floorings (tiles, parquet, fitted carpet, etc.).

Liquid product best for paving protection, formulated on the basis of acrylic resins with excellent hardness and ultraviolet ray resistance, dissolved in aromatic solvents.
Hardens through solvent evaporation and is especially advisable for concrete varnish, cut stone, etc, both in the interior and in the exterior, leaving a protective and decorative film with excellent properties.

Natural hydraulic-lime mortar for smoothing. Natural composition, highly breathable.

TEXTUREFIX-120 is a water-based acrylic vinyl primer, to be used in construction as a bonding bridge between new and old mortars. It presents a good capacity of penetration and cohesion, due to its particle size and good residual tack. It is also able to improve the adhesion conditions of the substrate in vertical supports, as a step prior to the application of the coating. Especially recommended for use as a primer before applying our mortar printed MORCEM TEXTURE (vertical supports).

Thixotropic mortar of high strength, with fiber  for concrete  repair and protection , based on nano-silane technology . Classification R4

Bi-component, epoxy resin-based primer in aqueous solution with mineral loads, for the preparation of concrete surfaces before the application of acrylic and epoxy-acrylic sports flooring systems. This flooring product has excellent adhesion to cementitious and concrete surfaces. It is easy to apply and can be used both indoors and outdoors. Preparation of concrete surfaces before application of the PAVILAND SPORT systems.

Synthetic mineral render, suitable for the waterproofing and decoration of façades and indoor walls.  Decorative coating in Exterior Thermal Insulation Systems TRADITERM (SATE / ETICS) and Morcemcal range of products.

Coloured epoxy resin, for the preparation of multilayer pavements of 2 to 4 mm thicknesses, great adherence and mechanical and chemical resistance. These kind of pavement products are easy to apply and have a great anti-slippery system. Suitable as cladding and sealing layer. Waterproof in interior floors. Available in a wide range of colours. Among its different uses we can find the ones in food, chemical and pharmaceutical industry or even laboratories.

Tile adhesive. For setting indoor and outdoor ceramic flooring, and indoor walls. Suitable for bonding ceramic tiles with a medium-high absorption rate. Ideal for conventional cement-based substrates. In addition, this cement-based adhesive has good workability and high bond strength.

Cladding mortar based on aerial lime. Suitable for plastering in thick layers, on ceramic brick, concrete block or any other similar substrates. Impervious to rainwater and highly permeable to water vapour.

Self-levelling mortar fast and high performance, for indoor floors preparation. Once hardened, it is suitable for all kind of light floorings (tiles, parquet, fitted carpet, etc.). Mortar for levelling floors in interiors High mechanical resistance and good resistance to abrasion. This self-levelling mortar is fast hardening and suitable for radiant heating. It has a high self-levelling power. 

Permeable smooth cladding based on watery dispersion of acrylic copolymers, pigments and special additives. Highly recommended on concrete, brick and any other cement-based façades where a maximum resistance and quality is required. Product available in our Easy-Colours tintometer system.

Liquid product best for paving protection, composed of an acrylic copolymer dissolved in aromatic solvent.  Hardens through evaporation of solvents and acts by penetrating and compacting the particles, increasing paving cohesion both in interior and exterior applications.

TEXTUREFIX PLUS is a priming product for use in construction as a bonding coat between new and old mortar. It has a good penetration and cohesion capacity due to the size of the particles.It is also capable of improving adhesive conditions on vertical substrates as a prior step to applying facings. Recommended as a bonding agent for paintwork, especially on plaster facings, perlite and old substrates.It also acts as a primer for regulating the absorbency of substrates such as cellular concrete or silico-calcareous brick, suitably treating substrates with high humidity or irregular absorption levels in order to keep the plasterwork uniformly hydrated after plastering. 

Natural hydraulic-lime mortar for brickwork. Natural composition, highly breathable.

Starter and protection profile used in the TRADITERM® System. It protect and reinforce the base. Used as a guide for the aligning the insulation panels. It does not rust and its easy to apply. It has a range of thicknesses to choose depending on the thickness of the insulation panel used.

Fast-setting binder. Designed as a setting and hardening regulator for making fast-setting mortars with high strength and dimensional stability.

1m x 10m x 4kg/m² plastomer (APP) modified bitumen membrane, with fiberglass reinforcement, finished with non-stick polyethylene film on the inside and mineral granule as protective material on the outside.Self-protected bituminous waterproofing membrane of the type LBM-40/G-FV.

A liquid release agent used in the execution of stamped pavements to prevent concrete or mortar from adhering to the moulds. This product for pavements allows immediate demoulding after application. Great anti-adhesion power. It prevents the appearance of efflorescences.

PAVILAND ARQ BASE is a high quality polymeric mortar for preparing and smoothing surfaces before installing microcement decorative smooth finishes. The maximum thickness for application is 4mm. Base coat from the Paviland Arq Base systems from Grupo Puma.

Synthetic mineral render, suitable for the waterproofing and decoration of façades and indoor walls and ceilings. 

• Internal or external use.
• On walls and ceilings.
• Decorative coating in Exterior Thermal Insulation Systems TRADITERM (SATE / ETICS) .

Thin-grained, coloured, two-component, acrylic-epoxy coating that acts as an intermediate coat in sports floors subjected to a significant degree of mechanical wear. This product for floors is very easy to apply and suitable for both interior and exterior areas. Suitable for sport areas floors subjected to intense use. Also suitable for highly durable bike lanes or outdoor car park areas with very low road traffic.

Dry siliceous aggregates of different granulometries for dusting or mixing in systems or products of the PAVILAND range. It is an aggregate of great hardness and stability. Useful for making anti-slip pavements. Dusting for primers and preparation of coatings and pavements in the PAVILAND EPOXI range.

Implarest PU is a two-component semi-elastic cladding of polyurethane free from solvents. It prepares the surface for the application of water repellent claddings of great thickness and great resistance to abrasion.

Cladding mortar based on aerial lime. Suitable for being plastered in a thin layer on top of rough-coating cement mortars. Impervious to rainwater and highly permeable to water vapour.

Primer indicated to favour the anchorage of paints and coatings in restoration. It regularises the absorption of the foundations and superficially consolidates inconsistent foundations.

Self-levelling mortar for interior residential floors that once  harden accepts any kind of pavements: ceramic, parquet, etc. 2mm to 10 mm thickness. Mortar for levelling irregular pavements indoors. High mechanical resistance. Easy to lay and high self-levelling power.

Decorative and protective coating used as finish coat on all kind of vertical and horizontal walls, both indoors and outdoors, such as concrete, brick, fibre cement boards, etc. It stands out for its whiteness and its great covering power.

2-component fast curing vinylester injection resin.

Natural hydraulic lime breathable grout for consolidating masonry walls. Natural composition.

PAVILAND ARQ FINISH is a coloured polymeric decorative finish for high quality interior and exterior applications with a maximum thickness of 1.5 mm. Finishing coat in the Paviland Arq systems.

Two-part, epoxy resin-based primer in aqueous solution with mineral fillers, for the preparation of concrete bases before application of acrylic and epoxy-acrylic sports floors systems; for outdoor use.

Mineral mortar for the regularization, levelling and smoothing of surfaces with a thin finish, suitable for absorbent and non-absorbent supports, for  white interior and exterior areas.

Quartz aggregate of different colours for industrial decorative pavements:  anti- slipping and self-levelling multilayer systems.

Protection and closing profile in External thermal insulation Traditerm Systems (SATE/ETICS). The TRADITERM® PERFIL CIERRE LATERAL protects and reinforces the side finishes of the Systems.TRADITERM® (thermal insulation), does not rust and is easy to install on site. It has a range of thicknesses to be chosen according to the thickness of the insulating panel used.

Reinforcement mesh for the assembly of the MORCEM ELASTIC PM waterproofing membrane in areas or points described in this document.

Rugged coating best for exterior vertical facing of concrete, brick and construction material based on cement.

Corner reinforcement profile in perforated PVC, used in the TRADITERM® System. This component of the system is easy to apply. The incorporation of the mesh into the profile, makes it quicker to do the corner and allowing an optimal functioning.

Pure acrylic resin dispersion with low water absorption. Suitable for curing concrete on courts, industrial flooring, and continuous flooring in general. It controls water evaporation, regulating the drying time and contributing to a slow curing process which increases the final mechanical strength, achieving more durable surfaces and the maximum development of their hardness.

Injection resin for anchorage, 2-component and fast curing, resin-based polyester. Styrene-free. Multifunctional, for solid or hollow substrates.

R3 mono-component medium resistant repair mortar.

Cementitious adhesive of mixed binders  with reduced slip and extended open time, for the installation of interior and exterior floors, interior walls, and exterior plinths. Specially designed for installing new flooring over existing surfaces. Adhesion of all types of ceramic pieces, porcelain stoneware, marble, granite, and natural stone.

Polyurethane foam tape with an adhesive acrylic impregnation on one side. Hermetic and watertight sealing of the external joints thanks to its dimensional tolerance on leveling.
 

Dry mortar. Designed for usual and ordinary masonry applications in which a rapid and high performance mortar is required.

Liquid product best for the concrete curing process in order to promote its maximum performance. Controls hydration water evaporation regulating dry out time and favours slow curing to achieve an increase of final mechanical resistance, achieving more tenacious surfaces and the maximum development of its hardness.
Acts on the surface forming a plastic closing capable of eliminating systematically the formation of cracks and of controlling superficial retraction.

Two component flexible waterproofing mortar.

High-performance, one-component, neutral and elastic filler for sealing and bonding.

Aluminium perforated reinforcing corner profile, used with the TRADITERM® System. Its easy to apply and the incorporation of the mesh to the profile makes the corner much faster to use.

Self-levelling covering, normal setting, which once hardened, creates a highly flat surface with high mechanical strength and excellent bonding performance to the substrate. Suitable for thicknesses from 5 to 15 mm.  This self-levelling coating boasts ease of laying and excellent adhesion to cementitious mortars and concrete. It has great levelling capacity as it is a levelling mortar for irregular floors indoors. Renovation of parking pavements.

Pigment for Paviland^® ARQ range.

Cementitious adhesive made of mixed binders, non slip  and extended open time. Suitable for interior and exterior pavements, interior claddings and baseboards. Suitable for the placing  for all kind of ceramic pieces, porcelain clay, natural stone, granite and marble. High grip strength, good workability and aging resistance.

Mortar for construction and cladding, for reinforcing reinforced cladding and masonry fill, fibre-reinforced, made of natural hydraulic lime. Natural composition, breathable to water vapour. High mechanical resistance.

Barrier against capillary moisture Cream product that, injected into the walls through drills, forms a permanent water-repellent barrier to prevent the rise of damp in building.

Coating mortar based on aerial lime. For plastering on cellular concrete blocks with fine scraping, polish or smooth finish.

One-component polyurethane-based filler for sealing or bonding.

Profile for reinforcing and forming guttering in the TRADITERM® thermal insulation system. Its morphology allows a correct evacuation of rainwater on the facade preventing the deterioration of carpentry and the Thermal Insulation System itself from the outside (SATE) in these meetings.

Impermeable mortar of two-components additives for the execution of impermeable coatings.

Self-levelling coating, fast drying, which hardened once creates a coating of high flatness, high mechanical strength and excellent adhesion on the support application. Suitable for thicknesses between 5 and 15 mm. This self-levelling coating boasts ease of laying and excellent adhesion to cementitious mortars and concrete. It has great levelling capacity and is ideal for use in cold weather. Renovation of parking pavements.

The Traditerm perfil arranque PVC cierre oculto forms, together with the different PVC starting profiles, the PVC base set for the level foundation of thermal insulation panels in the Traditerm / WalAce System (SATE/ETICS). It includes an invisible bellcast bead in PVC and a fibreglass mesh for a clean render finish and to guarantee vertical water drainage. 

Rapid setting cement prepared. To block water leaks in concrete cracks or fissures on other base-cement surfaces.

Morcem®Dry Mesh consists of double weave threads, essential for the reinforcing. 

Recommended in the application of swimming pool waterproofing systems as DryPool. Gives the system great resistance and stability, and prevents  the appearance of cracks caused by temperature differences or movements.

Waterproofing mortar. Semi Flexible.

Self-levelling, normal setting flooring mortar, pumpable, for levelling and smoothing interior industrial flooring. This product has high mechanical and substrate bonding strength once hardened. Thicknesses from 5 to 15 mm. For interiors: suitable as a finishing coat or base coat to be covered with fine coverings that provide the floor with greater chemical or physical protection, or for a more aesthetic finish. Self-levelling paving ideal for use in the cold season.

Acrylic priming monocomponent, based on resins in watery dispersion indicated for the preparation of the microcement surface before the application of the Paviland Arq Varnish. Fund of preparation of the completion varnish for the systems Paviland Arq.

Used in the Traditerm System. Reinforcing profile for the formation and reinforcement of arcs and circular gaps. Its fast and easy to apply. The profile can be easily folded and adapted to the curvature of the edge that needs to be reinforced. The minimum curvature diameter is 1m.

Finishing treatment for resin, cement or microcement pavements, which provides a surface, with bacteriostatic efficiency, high impermeability, easy cleaning, high resistance to abrasion and scratching. It highlights and beautifies the pavement. It has good resistance to abrasion and to the marks caused by the pedestrian traffic. It forms, at the same time, an effective bacteriostatic film, which makes it especially recommended both in local and public places.

Protect and reinforce the superior closing profile in External thermal insulation Traditerm Systems (SATE/ETICS). Its easy to apply and does not rust. There is a range of thicknesses to choose depending on the thickness of the insulation panel used.

Self-levelling floor with normal setting, pumpable, for levelling and smoothing industrial floors. Product with great mechanical resistance and adherence to the substrate once hardened. Suitable for thicknesses from 5 to 25 mm. Indoor applications: suitable as a finishing coat or as a base to be covered with thin coatings that provide the pavement with greater chemical or physical protection or a more aesthetic finish. Outdoors: use only as base layer, never leave exposed (a coating is mandatory).

Paint based on acrylic resins in water, micronized fillers and pigments, of a single component, which acts as a decorative, finishing and sealing layer on cementitious and concrete substrates. Surface hardener for cementitious floors that seals and protects the treated surface. Garages, interior floors or exterior parking areas with very low traffic. It has a good resistance to ultraviolet rays, since it does not discolor.

Water-based epoxy resin coating, consisting of two components that harden through a chemical reaction and are tolerant to substrates containing some residual moisture. This flooring product exhibits extraordinary adhesion to the substrate, even on wet surfaces. It is also permeable to water vapour and various aggressive agents. Among its characteristics are easy application and being odourless, making it ideal for use in indoor, poorly ventilated garages.

PVC profile, designed for corner reinforcement with an angle different to 90ºC in Aislamiento Térmico Exterior Traditerm Systems(SATE/ETICS). Used as corner reinforcement that doesn´t form straight angles. Its easy to apply and the incorporation of the mesh to the profile makes the execution of the corner faster.

Mortar for bases creation with subsequent placement of other coatings such as parquet, carpet, ceramic, etc. Its fast drying feature allows the application of ceramics within 24 hours, as well as the execution of other types of work with notable time savings compared to other conventional mortars. Suitable for pedestrian traffic and underfloor heating, allowing different application thicknesses: between 20 and 40mm for bonded screed and between 40 and 80 mm for floating screed.

PVC profile with anti-alkaline fibreglass mesh and flexible band for joint treatment. Designed as a solution for expansion and structural joints in the support where the TRADITERM® Exterior Thermal Insulation Systems (SATE/ETICS) is going to be installed.

MORCEMDRY PU UV Varnish is an elastic two-component aliphatic polyurethane coating with solvents. It provides resistant and elastic protective films against ultraviolet rays. In addition to that, these films are elastic and also offer great resistance against industrial environments and other pollutants.

Profile for connection and final finishing between the different TRADITERM® (EWI/ETICS) Systems and the existing carpentry on the façade.

Two-component epoxy resin-based coating that results in a coating with high mechanical and chemical resistance on concrete or mortar floors. This flooring product has exceptional adhesion to the substrate, high abrasion resistance, and very good chemical resistance to fuels, oils, greases, and acids.  Easy to mix and apply, its applications include industrial floors and warehouses, garages, or laboratories.

Two-component coating based on aliphatic polyurethanes, quick-drying with high chemical and abrasion resistance. Available in shine or matte finish. It has excellent adhesion to concrete, mortar, epoxy resins, and polyurethane resins. It also exhibits high abrasion resistance and very good chemical resistance.  This flooring product acts as a surface hardener for the substrate, providing good scratch resistance due to its toughness. Suitable for both interior and exterior floors.

PVC profile, designed for corner reinforcement in  external thermal insulation Traditerm Systems(SATE/ETICS). Its easy to apply and the incorporation of the mesh to the profile, makes the execution of the corner faster.

Anchor used to fasten insulation panels in the TRADITERM® System. Traditerm® Anchor is made of polyethylene and consists of two elements differentiated (nail and sheath). It is a percussion anchorage plug, used to fix the panels insulation in the TRADITERM Exterior Thermal Insulation System. It is easy to apply. It ensures a perfect fixing of the plates to the support. Resistant to oxidation. Wide range of product sizes for correct adaptation to thermal insulation systems depending on the thickness of the plate. European approval according to ETA-16/0509.

Anchor fixings with threaded screw, for fixing TRADITERM^® external insulation panels. High quality, secure anchor fixings. As it is a pre-assembled screw, it is easy and quick to install. It ensures a high quality fixing of the insulating panels to the support. With European Certification. Possibility of hidden anchorage in the system. Range of sizes, depending on the thickness of the panel. Use category according to ETA.

Acrylic primer, in aqueous solution, for the preparation of concrete and asphalt foundations before the application of acrylic and epoxy-acrylic sports flooring systems. Fixes and seals the foundation, regularizing its absorption. Suitable indoors and outdoors.

Anchor suitable for wooden substrates with zinc screw. Easy and fast execution. It ensures a fixation
of high quality insulating panels on wooden supports. Possibility of hidden anchorage in the system. Fixing of insulating panels to the External Thermal Insulation System Traditerm®(SATE/ETICS). Permanent contact pressure. Range of sizes, depending on the thickness of the insulating panel to be used.

Element for fixing light loads of up to 5 kg to the outdoor TRADITERM® thermal insulation system. Polyamide composite. Easy application. Does not generate thermal bridges.

Screw for mechanically fastening TRADITERM® 300 Mounting. This steel screw ensures that the rigid polyurethane element is fixed at four points, by anchoring this piece to the support, provided that the latter has suitable resistance conditions on its surface for its correct anchorage.

Expanded polystyrene cover to  fill in the gap lefts by the corona STR in the insulating panel when TRADITERM® TACO DE ANCLAJE STR U 2G is installed. Levelling of TRADITERM® PANEL EPS. Get the TRADITERM® TACO DE ANCLAJE STR U 2G hidden inside the insulation panel.