WalAce® Fixing Anchor
WalAce® Anchors are made up of polyethylene material and are used to fix the WalAce® insulation panels to the substrate. It comes in various lengths are per the Insulation thickness of WalAce® system. Also they have European approval according to ETA-16/0509.
Additional information
Composition
The anchor is formed of two elements: Nail: fiberglass reinforced polyamide Sheath: polyethylene
Features and applications
- Easy to apply.
- Ensures perfect fastening of the panels to the substrate.
- Resistant to corrosion.
- Available in various lengths depending on the thickness of the panel.
- Anchor with European certification.
Instructions for use
- After 24 hours from the fixing of the insulation boards to the facade with WALACE adhesive, using a drill, make a hole in the support, passing through the insulating panel.
- The depth of the hole in the bracket must be 60 mm.
- Place the WALACE FIXING ANCHOR in the hole made.
- With the help of a mallet, hit the anchor so that it penetrates until it cuts the surface by 1-2 mm of the insulation board.
- Subsequently, the recess produced on the surface of the insulating panel is regularized with the mortar WALACE®
Cautions and recommendations
- The plug must be inserted at least 50 mm into the holder.
- The plug must cut the insulation panel by 1-2 mm. If the plug is not inserted into the insulation, the insulation will marked on the final finish.
- Hammering into studs with nails already installed is not recommended as it may cause damage to the plate.
- The hole in solid materials should be cleaned of any debris prior to installation.
- Check that the blocks are securely fixed.
- Depending on the thickness of the insulation panel, the following thicknesses of WalAce FIXING ANCHOR are recommended:
| Type of anchor | TRADITERM insulation board thickness (mm) | Anchor block length (10 mm thick adhesive mortar layer + 20 mm thick existing plaster layer) | Minimum number of anchors / m² (usual situations) | Homologation anchor block | |
| Substrates type A,B,C y D | Substrates type E | 6 | ETA-16/0509 | ||
Walace® Fixing anchor |
30 | 90 | 110 | ||
| 40 | 110 | 120 | |||
| 50 | 110 | 140 | |||
| 60 | 120 | 140 | |||
| 70 | 140 | 160 | |||
| 80 | 140 | 160 | |||
| 90 | 160 | 180 | |||
| 100 | 160 | 180 | |||
| 120 | 180 | 200 | |||
| 140 | 200 | 220 | |||
| 150 | 220 | 260 | |||
| 160 | 220 | 260 | |||
| 180 | 260 | 260 | |||
| 200 | 260 | - | |||
Packaging
Boxes with the following format (depending on the length of the anchor):
| Thickness of Insulation Panel (mm) | Packaging |
| 90 | 200 no |
| 110 | |
| 120 | |
| 140 | |
| 160 | |
| 180 | |
| 200 | |
| 220 | 100 no |
| 260 |
Store the anchors in a dry place and avoid direct exposure to the uv rays. Shelf life of these anchors is : 5 years.
Technical data
(Data obtained in a laboratory under standard conditions)
| Composition | Polypropylene |
| Pre-drill diameter | 10mm |
| Drilling depth in holder | 60mm |
| Washer diameter | 60mm |
| Anchorage depth | 50mm |
| Homologation | ETA-16/0509 |
| Performance | 8 units/m2 |
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by PIDILITE GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
PIDILITE GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of PIDILITE GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by PIDILITE GRUPO PUMA´s products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
PIDILITE GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of PIDILITE GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by PIDILITE GRUPO PUMA´s products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
