Paviland® Industrial
Powder product which is applied over fresh concrete to form an abrasion resistant monolithic wearing course, for use on industrial flooring.
Additional information
Composition
High resistant Portland cement-based product, quartz, selected aggregates, pigments and additives of high purity.
Features and applications
- Industrial flooring.
- High mechanical resistance.
- High resistance to abrasion.
- Diverse range of colours.
- Unchangeable in every weather condition.
Instructions for use
- Prepare the substrate with appropriate concrete reinforcement mesh.
- Protect the areas that must be kept clean.
- Pour on the concrete and smooth with the trowel.
- Set the levels to level off the surface.
- The concrete levelling off can either be done with a vibrating concrete trowel, or manually.
- Pass over the power trowel ("helicopter") to open the concrete.
- Sprinkle the layer of wearing that forms PAVILAND INDUSTRIAL over the fresh concrete.
- Pass the "helicopter" over again to obtain a uniform layer of wearing, until it is completely smooth and hardened.
- Apply the curing resin.
- Cut and wash the expansion joints.
Cautions and recommendations
- Do not apply under 5ºC nor above 30ºC.
- Do not apply when there is a risk of frost, rain, strong wind or direct sunlight.
Packaging
25 kg plastic-lined paper bags.
Shelf life: 1 year in sealed original packaging, sheltered from weather conditions and humidity.
Technical data
(Statistical data obtained under standard conditions)
| Appearance | COLOURED powder |
| Apparent density of powder | 1.9 ± 0.2 g/cm³ |
| Approximate performance | 4 Kg/m² for an average thickness of 0.5 cm |
| Bending (UNE-EN 1015-11) | > 6 N/mm² |
| Compression (UNE-EN 1015-11) | > 35 N/mm² |
| Abrasion (UNE-EN-12808-2) | < 600 mm³ |
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.