Paviland® Impreso
Powder product that forms a monolithic surface highly resistant to abrasion. Stable texture and assorted patterns which can replace traditional floorings (paving stones, natural stones, slate, etc) when applied on fresh concrete.
Additional information
Composition
Product based on high resistance Portland cement, selected aggregates, pigments and high purity additives.
Features and applications
- Streets, pavements, outdoor areas and shopping centre entries, town streets with pedestrian and car traffic, entries and surrounding areas of single-family houses, swimming pools, residential areas, etc.
- Carparks. Parking areas.
- Walking areas in parks and gardens.
- Finishes in public squares.
- High mechanic resistance.
- High resistance to abrasion.
- Variety of textures and colours.
- Possibility of combining different types of stamped patterns.
- Patterns and tones are easily obtained by choosing the right mouldings and powder colors.
- Wearing resistant. Fading resistant.
Instructions for use
- Prepare the substrate with the appropriate mesh to reinforce the concrete.
- Protect the areas that must be left clean.
- Pour the concrete and smooth with the trowel.
- Dust PAVILAND STAMPED on the fresh concrete.
- Smooth down with telescopic trowel so that the concrete can absorb the surface coat formed by PAVILAND STAMPED.
- Ensure that PAVILAND STAMPED fully covers the application areas. Use more product if in doubt and trowel again.
- After a reasonable time, when the concrete has started hardening, dust PAVILAND DEMOULDING AGENT to avoid the adherence of the moulds.
- The moulds are set and pressed uniformly, so that the pattern is stamped in an even way.
- Wait 72 hours and then clean the demolding agent from the flooring by means of water pressure jet..
- Finish the flooring by applying a hardening resin (the use of a pump is highly recommended).
Cautions and recommendations
- Do not apply below 5ºC nor above 30ºC.
- Do not apply when there is a risk of frost, rain, strong wind or direct sunlight.
Packaging
25 kg plastic-lined paper bags.
Shelf life: 1 year in sealed original packaging, sheltered from weather conditions and humidity.
Technical data
(Statistical data obtained under standard conditions)
| Aspect | COLOURED powder |
| Apparent density of powder | 1,8 ± 0,2 g/cm3 |
| Approximate yield | 4-6 kg/m2 |
| Slipperiness | R3 |
Note
The instructions for use are given according to our tests and knowledge and do not imply any commitment by GRUPO PUMA nor free the consumer from the examination and verification of the products for their correct use. Claims must be accompanied by the original packaging to allow a proper traceability.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.
GRUPO PUMA is not responsible, in any case, for the application of its products or constructive solutions carried out by the application company or other parties involved in the process and / or execution of the work, limiting the responsibility of GRUPO PUMA exclusively to the damages directly attributable to the supplied products, individually or integrated in systems, due to failures in their manufacturing process.
In any case, the drafter of the work project, the technical management or the person responsible for the work, or collaterally the application company or other parties involved in the process and / or execution of the work, must ensure the suitability of the products addressing the characteristics of them, as well as the conditions, support and possible pathologies of the work in question.
The values obtained by GRUPO PUMAS's products or its constructive solutions that, as the case may be, are determined by the EN standards or any other regulation that applies to it in each case refers exclusively to the conditions specifically stipulated in said regulation and that are referred to, among others, to certain characteristics of the support, humidity and temperature conditions, etc. without being them required in the tests obtained under different conditions, all in accordance with the relevant regulation.